您好!欢迎来访东营市兴达土方工程有限公司!关于我们 | 联系我们 | 在线留言
服务热线
18678687777(来经理)
联系我们
联系人:来经理
联系电话:13793968666
地址:山东省东营市广饶县
新闻中心

挖掘机系统故障怎么检查?

日期:2018-10-24   来源:http://www.dybocheng.com
1. 行走跑偏
1. walking deviation
该挖掘机发作行走跑偏毛病,在确定行走马达技能情况正常、履带松紧度调整恰当的情况下,作如下排查:
When the excavator has run off the track, the following checks are made to ensure that the running motor is in normal condition and the track tightness is properly adjusted:
(1) 查看中心反转接头
(1) check the center reverse connector.
中心反转接头处油道许多,相互之间简单勾结。先拆开 2 个行走马达的油管,然后堵死其间 1 个马达油管;再发动发动机,拉动堵死油管马达的换向阀,发现油液压力过低,而没有堵死的液压马达的油孔出油。由此断定中心反转接头的油道密封欠好。替换中心反转接头的密封件,毛病不见
There are many oil channels at the center reverse junction, which are simply colluded with each other. First, remove the tubing of two walking motors, and then plug the one motor tubing in between; then start the engine, pull the reversing valve plugging the tubing motor, found that the hydraulic pressure is too low, and no plugged hydraulic motor oil hole oil. It is concluded that the oil seal of the central reverse connection is not good enough. Replace the seal of the center reverse connector. It's not seen.
(2) 查看组合阀
(2) check the combination valve.
加长臂挖掘机
先查看行走速度慢一侧的行走组合阀。拆开其限压阀上的 2 根油管,用堵头堵住出油口,发动发动机,拉动有堵头组合阀的行走操作手柄,检测油压正常;再拆开另一侧行走组合阀上的 2 根油管,再次发动发动机,调查其限压阀的 2 个油孔无油液流出,由此判别毛病不在组合阀。
First look at the walking speed slow side of the combined valve. Remove the two tubing on the pressure limiting valve, plug the outlet with a plug, start the engine, pull the walking handle of the combination valve with a plug to check the normal oil pressure; then remove the two tubing on the other side of the combination valve, start the engine again, investigate the two oil holes of the pressure limiting valve without oil flowing out, thereby distinguishing the hair. The disease is not in the combination valve.
2. 斗杆油缸弹性缓慢无力
The 2. bucket cylinder is slow and elastic.
该挖掘机在作业过程中呈现斗杆油缸弹性缓慢无力毛病,经剖析作如下排查:
The bucket-rod cylinder of the long-arm excavator shows slow elasticity and weakness during its operation. The analysis is made as follows:
(1) 查看密封件
(1) check seals.
若斗杆油缸活塞等处密封件失效,将形成低压腔与高压腔的液压油因内泄而互窜。先松开低压腔的油管,放掉腔内液压油,然后发动发动机给高压腔内写入压力油,未见液压油从低压腔的油管中流出,标明斗杆缸活塞密封件密封杰出。
If the sealing parts of bucket rod cylinder piston and other places fail, the hydraulic oil of low pressure cavity and high pressure cavity will be channeled each other because of internal leakage. First loosen the oil pipe in the low pressure chamber, release the hydraulic oil in the chamber, and then start the engine to write the pressure oil into the high pressure chamber. No hydraulic oil flowed out of the oil pipe in the low pressure chamber, indicating that the piston seal of the bucket rod cylinder is outstanding.
(2) 查看吸油阀
(2) check the safety suction valve.
斗杆油缸作业回路上装有 2 个吸油阀,若其间某个吸油阀的单向阀失效成为双向直通,或许在溢流阀溢流压力很低时,都会形成该侧油腔的油压不能树立,压力油直接经过单向阀或溢流阀泄入油箱,使斗杆缸动作缓慢无力乃不能作业。
There are two safety suction valves in the working circuit of the bucket rod cylinder. If one of the safety suction valves fails to be two-way through during the operation, the oil pressure in the side chamber may not be set up when the overflow pressure of the relief valve is very low, and the pressure oil will be discharged directly into the tank through the one-way valve or the overflow valve, thus slowing down the action of the bucket rod cylinder. Unable or even unable to work.
吸油阀若发作上述毛病,在操作手柄处于中立方位停机后,斗杆油缸会主动缓慢回落。但是该斗杆缸没有发现此种表象,阐明毛病不在吸油阀
If the safety suction valve has the above problems, the bucket rod cylinder will slow down actively after the operation handle stops at the neutral position. But the bucket cylinder did not find such a representation, indicating that the fault was not in the safety suction valve.
以上就是给大家分享的内容了,想要了解更多的精彩内容请点击进入我们的网站http://www.dybocheng.com,或者是搜索我们的关键词挖掘机查找,我们会有更多的精彩内容与您分享!
That's all for you to share. For more exciting content, please click on our official website http://www.dybocheng.com, or search our keyword lengthening arm excavator for more exciting content to share with you!


【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】