长臂挖掘机

省时 省力 省财富

挖钢板是考验挖机手技术的时候，想要将钢板架在铲斗之上不掉落，说起来简单做起来难，稍有操作不当就容易掉落，还有可能对挖机造成不必要的伤害，小编就给大家介绍一下长臂挖掘机挖钢板的几种好方法。

The steel plate digging is a test of the excavator's skill. If you want to put the steel plate on the bucket without dropping, it is simple to say but difficult to do. It is easy to drop if you do not operate properly. It may also cause unnecessary damage to the excavator. Xiao Bian will introduce several good methods of long arm excavator to dig steel plates.

挖坑法

Pit digging method

直接的一种方式就是在钢板前挖个坑，用挖斗将钢板挖起来就OK了，不过这有个前提，钢板不是在水泥地上。

The direct way is to dig a hole in front of the steel plate and use a bucket to dig up the steel plate. However, there is a premise that the steel plate is not on the cement ground.

台阶法

Step method

还可以在钢板靠近挖机的方向挖个台阶，台阶作为支点防钢板滑落，不过挖台阶方式有一定局限性。

It is also possible to dig a step in the direction where the steel plate is close to the excavator. The step serves as a fulcrum to prevent the steel plate from slipping, but the step digging method has some limitations.

斗齿与铲斗空隙法

Bucket tooth and bucket clearance method

将铲斗斗齿插到钢板底部，利用斗齿到铲斗边刃之间的空隙，将钢板咬住，利用杠杆支撑的原理，将钢板提起。

Insert the bucket teeth into the bottom of the steel plate, use the gap between the bucket teeth and the bucket edge to bite the steel plate, and use the principle of lever support to lift the steel plate.

不过只适用于薄钢板，钢板过重的话有可能损坏挖斗。

However, it is only applicable to thin steel plate. If the steel plate is too heavy, it may damage the bucket.

搭履带法

Track method

一：用铲斗将钢板一边勾起，将钢板翻过来，使钢板的一边搭在履带上。

1： Use the bucket to hook up one side of the steel plate and turn it over so that one side of the steel plate rests on the track.

二：用挖斗挖起钢板的另一端。

2： Use a bucket to dig up the other end of the steel plate.

三：利用履带来调节钢板的前后距离，或者直接利用履带将钢板推入铲斗。

3： Use the track to adjust the front and rear distance of the steel plate, or directly use the track to push the steel plate into the bucket.

铲斗履带共进退法

Bucket track forward and backward method

一：将钢板拨到履带边。

1： Pull the steel plate to the track edge.

二：用斗齿将钢板的一边挑起。

2： Lift up one side of the steel plate with bucket teeth.

三：铲斗尽量插到钢板底部。

3： Insert the bucket into the bottom of the steel plate as far as possible.

四：慢慢勾起铲斗的同时，后退履带。

4： Back up the track while slowly lifting the bucket.

五：利用履带将钢板的一边卷起，同时继续做勾铲斗操作。

5： Use the track to roll up one side of the steel plate, and continue to hook the bucket at the same time.

六：直到钢板架在挖斗之上，钢板就挖起来了。

6： Until the steel plate is placed on the bucket, the steel plate is dug up.

上面关于挖掘机挖钢板的经验与技巧，希望能给各位挖机手们提供一点帮助！更多相关的内容就来我们网站http://www.dybocheng.com进行咨询！

The above experience and skills about digging steel plates with excavators can help you! More relevant content will come to our website http://www.dybocheng.com Consult!