您好!欢迎来访东营市兴达土方工程有限公司!关于我们 | 联系我们 | 在线留言
服务热线
18678687777(来经理)
联系我们
联系人:来经理
联系电话:13793968666
地址:山东省东营市广饶县
常见问题

如何快速找到挖机的漏油点?

日期:2023-01-30   来源:http://www.dybocheng.com
铲斗油缸、电机、液压泵等部件漏油是挖掘机平时施工过程中常见的问题,如果遇到不明位置漏油,漏油原因不清楚,不仅费钱费力,还耽误工作时间。挖掘机漏油怎么快速找到漏油点?加长臂挖掘机出租厂家为您解析。
Oil leakage from bucket oil cylinder, motor, hydraulic pump and other components is a common problem in the construction process of excavator. If there is oil leakage at an unknown location, the cause of the oil leakage is not clear, which not only costs money and effort, but also delays the working time. How to find the oil leakage point quickly when the excavator leaks oil? The rental manufacturer of extended-arm excavator will analyze for you.
基本上出现挖机漏油问题,车主都会先自己进行简单的维修,这样可以节省成本,节省时间,不耽误工程进度,前提是找准漏油点。今天挖掘机培训小编就给大家介绍一下,挖机漏油怎么快速找到漏油点,帮助挖机机主检修。
Basically, if there is an oil leakage problem of the excavator, the owner will carry out simple maintenance on his own first, which can save cost, save time and delay the progress of the project. The premise is to find the oil leakage point accurately. Today, the editor of excavator training will tell you how to quickly find the oil leakage point and help the excavator master to repair.
来看一位机主反馈的故障现象:挖机漏油,机子工作2-3分钟,发现先导阀块有液压油渗出。检查外观没有异常情况,所以找到维修师傅检查。
Take a look at the fault feedback from a machine owner: the excavator leaked oil, the machine worked for 2-3 minutes, and hydraulic oil was found leaking from the pilot valve block. Check the appearance and there is no abnormality, so find the maintenance technician to check.
加长臂挖掘机出租
挖机漏油故障检查情况:
Inspection for oil leakage of excavator:
维修工到达现场后先将油擦干净。启动机器不到3分钟,阀块底板已经开始滴油。由于阀块连接的管道只有几根,所以所有的管接头都再次拧紧,故障仍然存在;换上新阀块后发现还漏油;拆下电磁阀块固定螺钉,吊起阀块,擦干净继续工作,工作一段时间后迅速检查,发现漏油点,原阀块加工工艺孔漏油,拧下工艺孔内六角螺钉,安装小O圈,拧紧故障排除。
After arriving at the site, the maintenance worker should wipe the oil clean. Less than 3 minutes after starting the machine, the valve block base plate began to drip oil. Since there are only a few pipes connected to the valve block, all pipe joints are tightened again, and the fault still exists; Oil leakage was found after replacing the valve block; Remove the fixing screws of the solenoid valve block, lift the valve block, wipe it clean, and continue to work. After working for a period of time, quickly check and find the oil leakage point. The original valve block processing process hole has oil leakage. Unscrew the hexagon socket screws of the process hole, install the small O-ring, and tighten the troubleshooting.
处理结果:维修师傅在工艺孔里加了一个O形圈,排除了故障。
Treatment result: the maintenance technician added an O-ring in the process hole and eliminated the fault.
检修查找故障需要仔细观察,我们必须尽力找出故障的原因。而一些液压配件,由于加工工艺原因,需要打孔,如果工艺孔处理不好,也会造成漏油等故障。
Careful observation is required for troubleshooting, and we must try to find out the cause of the fault. Some hydraulic parts need to be punched due to processing technology. If the processing hole is not properly handled, it will also cause oil leakage and other faults.
上面案例仅是一种挖机漏油情况,实际挖掘机操作中会遇到各种各样的情况,检查故障问题一定要耐心和细致,尽可能掌握更多的特殊故障处理经验和技巧,这样可以尽快确定故障点在哪里,而不是浪费时间和精力!更多相关内容就来我们网站http://www.dybocheng.com咨询!
The above case is only a case of excavator oil leakage. In actual excavator operation, various situations will be encountered. The inspection of fault problems must be patient and careful, and more special fault handling experience and skills should be mastered as much as possible, so that the fault point can be determined as soon as possible, rather than wasting time and energy! Come to our website for more relevant content http://www.dybocheng.com consulting service


【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】