• 东营博诚长臂挖掘机出租公司
  • 联系人:王经理
  • 手机:18766733030
  • 地址:山东省东营市
  • 网址:www.dybocheng.com
新闻中心当前位置:首页-新闻中心
    挖掘机例行保养规程
    来源:www.dybocheng.com 2018-1-11 14:54:52

    1.加长臂挖掘机检查燃油箱油量,根据需要,加足燃油。
    1. add the long arm excavator to check the fuel tank oil, and add the fuel according to the need.
    2.检查燃油箱油管、管接头及滤清器,如有渗漏,应予排除。
    2. check oil tank tubing, pipe joint and filter, if there is leakage, should be excluded.
    3.检查油底壳机油油位,应将机器置于水平位置进行,油位应在油标尺上、下刻线之间,不足时加足。如油位过高,应查明原因,排除故障。
    3. to check the oil level of oil base oil, the machine should be placed in the horizontal position. The oil level should be between the oil scale and the lower line. If the oil level is too high, the reason should be found out and the fault is excluded.
    4.检查机油管、管接头及滤清器,如有渗漏,应予排除。


    加长臂挖掘机4. the oil pipe, pipe joint and filter, if there is leakage, should be excluded.
    5.检查水分离器,排放水分离器内的积水。
    5. check the water separator and discharge the water in the water separator.
    6.检查冷却系进风道,加长臂挖掘机进风道应经常保持畅通,如积有尘土杂物,应及时排除。
    6. check the inlet duct of the cooling system, and the inlet duct of the long arm excavator should be kept smooth, such as the dirt in the dust, which should be eliminated in time.
    7.检查进排气管的接合部位,如有漏气现象,应予排除。
    7. check the joint parts of the intake and exhaust pipes, such as gas leakage, should be excluded.
    8.清洁滤清器排尘阀的排放口,当集尘器中尘土量达到一半时,应立即去掉尘土,清洁集尘器。
    8. the exhaust valve of the cleaner filter, when the dust of the dust collector reaches half the dust, the dust should be removed and the dust collector should be cleaned.
    9.检查各零部件的紧固情况,各零部件应连接紧固、可靠,如有松动,应按规定力矩予以紧固。
    9. check the fastening of each component, each part should be fastened and reliable, if loose, it should be fastened according to the specified torque.
    10.听发动机运转情况,发动机应起动迅速。各速应运转正常,无异响、异烟,否则应查明原因,排除故障、走合期间工作50小时后,应紧固缸盖螺栓,检测气门间隙,如有不符,应按规定予以调整。
    10. to hear the engine running, the engine should start quickly. The speed should work normally, no noise or smoke. Otherwise, we should identify the cause and remove the malfunction. After 50 hours' work, we should tighten the cylinder head bolts and check the valve clearance. If there is any discrepancy, we should adjust it according to the regulations.
    我公司会恪守商业信誉及平等互利的原则,竭诚为用户提供最优良的服务,创作更加完美的作品,诚愿与各界朋友携手奋进,共创繁荣。
    Our company will abide by the principles of business reputation and equality and mutual benefit, and provide users with the best service and create more perfect works. We are willing to work together with friends from all walks of life to create prosperity.